9 Tips to Guard Against Aflatoxin in Corn
KSU Extension swine specialists Mike Tokach and Joel DeRouchey outlined several points for producers to keep in mind regarding feeding corn to swine
August 26, 2011
Soaring temperatures and drought conditions through parts of Kansas and other states are sparking some cases of aflatoxin in corn, which means swine producers should be vigilant about what they’re feeding, according to Kansas State University (KSU) scientists.
“Aflatoxin is a toxic metabolite produced by the ear-rotting fungus Aspergillus flavus,” says Doug Jardine, state plant pathology leader with KSU’s Research and Extension. “It is favored by hot, humid and droughty conditions during the grain fill period.”
KSU Extension swine specialists Mike Tokach and Joel DeRouchey outlined several points for producers to keep in mind regarding feeding corn to swine.
1. Harvest contaminated corn fields as quickly as possible. Once it appears, toxin levels appear to continue to increase in fields due to mold growth.
2. Clean the grain if possible before storage. Removing damaged kernels lowers toxin levels (by about 50%).
3. Store at less than 15% moisture (13% or less is ideal) to limit further fungal growth and toxin production.
4. Flush to clean the system after handling contaminated corn (put flush in a contaminated bin).
5. Consider adding propionic acid to corn before it goes into storage if fungus is present and a concern. Add 0.5% of propionic acid to limit further fungal growth.
6. Monitor grain bin temperatures. Good grain management is important, as hot spots will increase fungal growth and toxin production.
7. Segregate corn into high and low level bins if possible. Corn with less than 20 parts per billion can be fed in sow, nursery and last finisher diets. Corn with greater than 20 ppb can be fed to finishing pigs.
8. Use low test weight corn quickly. It does not store well.
9. Monitor DDGS (distiller’s dried grains with solubles). Aflatoxin may be four times higher in DDGS than in the corn used to make it.
“Keep in mind that aflatoxin is a carcinogen, and that levels build up in the body over time,” Tokach says. “So, when feeding corn that contains aflatoxin, there may be reduced feed intake in the short term, but it’s the long term where the biggest negative impact can occur.”
When feeding in grow-finish situations, typically there is no adverse effect if corn contains under 200 ppb aflatoxin, but at 200 to 400 ppb reduced growth can occur and immune systems can be compromised, he says. At 400 to 800 ppb, liver lesions can occur.
When feeding aflatoxin-infected corn to sows, there is typically no effect under 100 ppb, Tokach says. If levels are in the 500 to 750 ppb range, pigs will grow more slowly due to aflatoxin in the sow’s milk. There does not appear, however, to be any effect on conception rates.
If feeding infected corn to nursery pigs, there is no effect if the aflatoxin is kept under 20 ppb, he says.
“Producers who have high aflatoxin corn should use a binder, such as bentonite or aluminosilicate at 10 lb/ton,” DeRouchey says. “Research shows that bentonite will bind up to 700 ppb of aflatoxin. You do not need to add a binder to finishing diets, except last finisher situations, if levels are under 200 ppb.”
Even though research shows that higher levels of aflatoxin can be tolerated when bentonite is added to the diet, Food and Drug Administration regulations require that corn fed to young pigs contain less than 20 ppb, for breeding animals less than 100 ppb, and for finishing pigs, less than 200 ppb. If the corn has greater than 200 ppb, FDA rules indicate that it should be blended with other corn to lower the level to 200 ppb or less before feeding. Blended corn must be used on-site and cannot be sold.
The swine specialists encouraged producers to use clean corn (less than 20 ppb) for nursery and lactating sows and feed corn with over 20 ppb aflatoxin to finishing pigs.
You May Also Like